---===1_FOREWORD_0001.djvu===---
2006 Hino Motors, Ltd. 
All rights reserved. This book may not be repro- 
duced or copied, in whole or in part, without the 
written permission of Hino Motors, Ltd. 
First Printing: June. 2006 
FOREWORD 
This supplement has been prepared to provide information covering general service repairs for DUTRO which underwent changes in June, 2006. 
Applicable models: XKU414M TKFQW series 
For the service specifications and repair procedures of the above model other than those listed in the supplement, refer to the following manuals. 
Manual Name 
Pub. No. 
S DUTRO Chassis Workshop Manual 
S1 YXZE05A 1/4 
S DUTRO Chassis Workshop Manual 
S1 YXZE05A 2/4 
S DUTRO Chassis Workshop Manual 
S1 YXZE05A 3/4 
S DUTRO Chassis Workshop Manual 
S1 YXZE05A 4/4 
S DUTRO Chassis Workshop Manual 
S1 YXZE10A 
S DUTRO Electrical Wiring Diagram 
S1 YXZE05A SL 
S DUTRO Electrical Wiring Diagram 
S1 YXZE10A SL 
S DUTRO Supplement For Chassis And Electrical Wiring Diagram 
S1 YXZE13A(SI) 
S N04C TF Engine Workshop Manual 
S5 YN04E01A 
S H260 Manual Transmission Workshop Manual 
S1 YXZE07A 
S SH12 Differential Workshop Manual Supplement 
S1 YXZE11A 
All information in this manual is based on the latest product information at the time of publication. However, 
specifications and procedures are subject to change without notice. 
If you find any failures in this manual, you are kindly requested to inform us by using the report form on the 
next page. 
---===1_FOREWORD_0003.djvu===---
Correction 
Proposal 
Pub. No. 
Subject 
Issue Date 
Name of 
Reporter 
Problem 
Name of 
Dealer 
Description 
Workshop Manual Quality Report 
Att.) Service Manager, 
Your Distributor 
---===1_FOREWORD_0004.djvu===---
CAUTION 
This manual does not include all the necessary items about repair and service. This manual is made 
for the purpose of the use for the persons who have special techniques and certifications. In the 
cases that non specialized or uncertified technicians perform repair or service only using this manu- 
al or without proper equipment or tool, that may cause severe injury to you or other people around 
and also cause damage to your customer 's vehicle. 
In order to prevent dangerous operation and damages to your customer's vehicle, be sure to follow 
the instruction shown below. 
S Must read this manual thoroughly. It is especially important to have a good understanding of 
all the contents written in the PRECAUTION of "INTRODUCTION" section. 
S The service method written in this manual is very effective to perform repair and service. When 
performing the operations following the procedures using this manual, be sure to use tools spe- 
cified and recommended. If using non specified or recommended tools and service method, 
be sure to confirm safety of the technicians and any possibility of causing personal injury or 
damage to the customer's vehicle before starting the operation. 
S If part replacement is necessary, must replace the part with the same part number or equivalent 
part. Do not replace it with inferior quality. 
S It is important to note that this manual contains various "Cautions" and "Notices" that must be 
carefully observed in order to reduce the risk of personal injury during service or repair, or the 
possibility that improper service or repair may damage the vehicle or render it unsafe. It is also 
important to understand that these "Cautions" and "Notices" are not exhaustive, because it is 
important to warn of all the possible hazardous consequences that might result from failure to 
follow these instructions. 
---===1_FOREWORD_0006.djvu===---
---===1_FOREWORD_0007.djvu===---
CHAPTER REFERENCES REGARDING THIS WORKSHOP MANUAL 
Use this chart to the appropriate chapter numbers for servicing your particular vehicle. 
VOLUME 
CHAPTER 
MANUAL NO. S1-YXZE15A 
MODEL 
DUTRO XKU414M-TKFQW 
STRUCTURES AND FEATURES 
(THE CHAPTERS FOR MAJOR 
CHANGES IN MODEL) 
ENGINE CONTROL SYSTEM 
10 
EMISSION CONTROL 
12 
INTAKE 
13 
ENGINE MECHANICAL 
14 
EXHAUST 
15 
HYBRID SYSTEM 
21 
WORKSHOP MANUAL : ENGINE PREPARATION 
2 
SERVICE SPECIFICATIONS 
3 
ENGINE MECHANICAL 
14 
STARTING & CHARGING 
19 
WORKSHOP MANUAL : CHASSIS INTRODUCTION 
1 
PREPARATION 
2 
SERVICE SPECIFICATIONS 
3 
DIAGNOSTICS 
5 
ENGINE CONTROL SYSTEM 
10 
FUEL 
11 
EMISSION CONTROL 
12 
INTAKE 
13 
ENGINE MECHANICAL 
14 
EXHAUST 
15 
COOLING 
16 
LUBRICATION 
17 
STARTING & CHARGING 
19 
HYBRID SYSTEM 
21 
TIRE & WHEEL 
28 
PARKING BRAKE 
33 
MANUAL TRANSMISSION / TRANSAXLE 
41 
CLUTCH 
42 
WIRING 
68 
---===1_FOREWORD_0008.djvu===---
---===1_FOREWORD_0009.djvu===---
STRUCTURES AND FEATURES 
ENGINE CONTROL SYSTEM 
EMISSION CONTROL 
INTAKE 
ENGINE MECHANICAL 
EXHAUST 
HYBRID SYSTEM 
---===1_FOREWORD_0010.djvu===---